Veteran-owned & operatedClear Lake, Minnesota · Locating since 2009

Field experience. Personal attention.

Utility locating
for your project.

Underground utility locating, fault finding, and GPS mapping. We’ll talk through what you need and the approach that fits your site.

Private Utility Locating

I identify and mark underground lines that could conflict with your work.

It starts with a conversation

Every project is a little different. We’ll talk about what you’re planning, where the work will take place, and anything you already know about the utilities. Any maps or background you have can help, but you don’t need all the answers before getting in touch—that’s part of what I’m here for.

I work with homeowners, contractors, farms, businesses, cities, government agencies, and utility companies. If you’re arranging locating as part of a contract, you can find more about that on the contractor locating page.

Working through what’s underground

Some lines are straightforward to follow; others take a little detective work. That’s a part of locating I enjoy. I draw on my experience, available records, and what I find on site to piece together how the utilities run through your work area. I’ll make every reasonable effort to locate and mark the lines we’re there to find.

Walking through the results together

Before I leave, we’ll go over the markings and what I found, with time for your questions. If a line needs additional access or another approach to locate it, I’ll talk through the options with you and explain what’s involved.

What kinds of lines can be traced?

Power, street lighting, low voltage, irrigation control wiring, gas and propane, communications, and water lines are common requests. These are examples, not a limit on the work I’ll consider.

Electromagnetic locating follows a signal along a conductive line or usable tracer wire. For a non-metallic pipe, suitable access may allow a sonde or traceable rod to be used. We’ll work through the options for the lines on your site.

BelowMark does not offer ground-penetrating radar (GPR).

When GPR helps and why I don’t use it

Where it can help. GPR scans from the surface without a direct connection to the line. With favorable soil and a shallow target, it can pick up some metal and plastic pipes, even without a tracer wire.

Where it can miss. Wet or clay-rich soil can weaken the radar signal. Deeper lines and small pipes are harder to pick up, and the usable depth varies from site to site. A scan with no clear return can still miss a buried line.

Why I don’t offer it. In the northern areas I serve, some utilities are buried too deep for me to count on a clear radar return. I choose the locating method based on the line and the access available.

Federal Highway Administration guidance on GPR

Acoustic water line locating

If a private water main or service line has no usable tracer wire, I’ll check whether acoustic locating is an option. With suitable access, I can send vibrations along the pipe and listen for them at the surface.

Depth, soil, background noise, and access can make the signal hard to follow. If the pipe has a suitable opening, a sonde or traceable rod may offer another way to follow the line.

Sewer line locating

Sewer lines are evaluated case by case. I can trace a usable tracer wire when one is accessible. With a suitable cleanout, I may be able to feed a small transmitter (sonde) or a traceable fish tape or rod into the pipe and follow the signal from the surface.

This can mark the route that the equipment can reach. Missing access, tight bends, obstructions, depth, or signal interference can limit how far I can trace. I’ll show you the marks and explain what access or follow-up would help extend the trace.

Finding a septic tank

If you’re unsure where the tank is, I may be able to flush a small transmitter designed for this purpose down a toilet that feeds the tank. I use a locator at the surface to find the sonde once it reaches the tank and mark the spot where I pick up its signal.

This can narrow down where to look without exploratory digging. The sonde has to reach the tank and produce a readable signal. Pipe conditions, depth, and interference can limit the result. The mark shows where I detected the sonde. Tank edges, lids, and the drain field need separate verification.

Fault Finding

Narrow down where to investigate a suspected underground wire fault before digging.

Common jobs

Site lighting that lost power, a dead irrigation zone, a broken invisible dog fence loop, or a suspected fault in a buried power feed.

How I investigate a fault

An A-frame can help narrow down some faults when a signal escapes into the soil. A clean break, branches, splices, multiple faults, limited access, or ground conditions can affect which checks are useful. The problem may also be above ground, at a controller, breaker, or connection.

I’ll walk you through what I found and where to focus the next check. If the problem is a loss of power, tell me whether it’s already been isolated to the underground feed.

GPS Utility Mapping

Request GPS data when you ask for a quote so I can include it in the scope and pricing.

Coordinates or a digital map

I use a Subsite UtiliGuard 2 RTK receiver to record GPS points for traced lines. I can provide coordinates or create a digital map of the traced routes.

A record of the locate

Paint and flags provide a reference in the field. Optional GPS mapping adds a digital record of the routes I trace. RTK improves the positioning of the recorded points; it does not independently detect a buried utility or guarantee its exact position.

Direct upload to your GIS

With a compatible Esri ArcGIS Online map, Subsite UtiliView can automatically upload the points I log in the field once the required layers and permissions are set up. Tell me which mapping system you use so we can confirm compatibility before the visit.

Tell me about your project.

Have a project coming up or a question about a buried line? I’m happy to help you work out the next step.

Request a Quote